About ROLLSROLLER
About ROLLSROLLER
ROLLSROLLER - Profitable signmaking Flatbed Applicators
ROLLSROLLER Flatbed Applicator® has revolutionized the finishing work of many of our customers. Using manual processes can make it difficult to meet customer’s growing demands. Many of the manual procedures are strenuous and demanding – and results can vary. ROLLSROLLER gives you perfect results in a third of the time.
PRODUCTION CAN START QUICKLY
ROLLSROLLER Flatbed Applicator is very easy to use. In just a couple of hours, a complete beginner will be producing finished signs of all sizes with perfect results, completely unassisted. This means that you quickly start earning back your investment. Simply put, your profits start right from day one. Using ROLLSROLLER is like riding a bicycle – once you’ve learned, you never forget.
- Fast ROI
- Profitable
- Easy to learn
FLATBED APPLICATOR DOES THE JOB IN A THIRD OF THE TIME
Above all, the ROLLSROLLER Flatbed Applicator saves you time – lots of time! Many of our customers have reorganised their whole production process and significantly raised their profits – partly because the ROLLSROLLER increases their capacity and partly because they have more time for other activities, such as sales.
- Increased capacity
- Shorter delivery times
- More times for sales and customer care
PERFECT RESULTS EVERY TIME
With traditional application by hand or using a roll to roll laminator, the results are often unreliable and a certain amount of wastage is unavoidable. ROLLSROLLER Flatbed Applicator significantly improves the final results by producing higher quality every time – whoever is doing the job.
- Higher quality – no more bubbles and creases
- Less wastage
- Consistent high quality – every time
ERGONOMIC WORK POSITION
Manual application on very large signs requires a lot of climbing and knee-bending, which puts strain on the body. The ROLLSROLLER Flatbed Applicator gives you an ergonomic work station. And by choosing a height-adjustable table, you get even greater benefits and can reduce the long-term accident and sick-leave rate at your workplace.
- Better ergonomics
- Less strain on the body
- Less sick leave
FAQ - ROLLSROLLER
FAQ- ROLLSROLLER
Eastsign supply professional and honest service.
THE RUBBER ROLLER WON’T MOVE UP AND DOWN
- Reset the emergency stop function
- Check the air connections
THE RUBBER ROLLER FALLS DOWN/GOES UNEVENLY
- Check air pressure
- Check green indicator lamp on the glide beam
- Look for leaking air connections
- Adjust the roller speed
THE MACHINE PULLS UNEVENLY DURING APPLICATION
- Check bearing play in the glide beam
- Perform a cross measurement of the roller
MACHINE CREATING CREASES/BUBBLES
- Perform a cross measurement of the roller
- Perform a pressure test and see if the roller presses evenly.
- Check quality of the vinyl/material. Has the liner been exposed to moisture?
- Try different method how to apply the vinyl
- If applying on boards, check thickness tolerances from the manufacturer of the boards
HEIGHT ADJUSTMENT
- Reset the system.
- Check main power.
- Unplug the socket to the main power, wait a few seconds. Plug the cable and reset again.
Resetting the height adjustable system:
- Disconnect power supply to the table, wait 60 seconds.
- Connect power supply, wait 25-30 seconds (the system feels that everything is connected.)
- Press the down key at one side and run the table into the lowest position. Hold the button during the hole process, legs will give a small motion up/down before reset is done.
- Repeat the reset (press down the down key) once again , to be sure that all the legs are in the lowest position.
- Now the system should be ok.
MAINTENANCE
EVERY DAY
- Make sure that the roller is not damaged and has nothing stuck to it.
- Check the emergency stop function and controls.
- Check visible cables for damages.
ONCE A WEEK
- Wipe any dust off the Glide beam’s sliding rails.
- Check filter regulator, empty for water if necessary.
- If your ROLLSROLLER has a compressor, see manual for maintenance instructions.
ONCE A MONTH
- Lubricate the sliding rails surfaces.
IF NECESSARY
- Check the bearing play in the Glide beam
- Dust the cutting mat with talcum powder
Additional resources:
Gypsum: production solutions - Building Materials
Pallets, part pallets and cartons calculator
(The cutting mat is dusted with talcum powder at the factory, but should be dusted again when needed. The talcum powder prevents vinyl, adhesive and other materials from sticking to the cutting mat. It also reduces the risk of getting wrinkles/bubbles during application/lamination as the material can ”float” on the cu
About ROLLSROLLER
ROLLSROLLER - Profitable signmaking Flatbed ApplicatorFlatbed Applicators
ROLLSROLLER Flatbed Applicator® has revolutionized the finishing work of many of our customers. Using manual processes can make it difficult to meet customer’s growing demands. Many of the manual procedures are strenuous and demanding – and results can vary. ROLLSROLLER gives you perfect results in a third of the time.
PRODUCTION CAN START QUICKLY
ROLLSROLLER Flatbed Applicator is very easy to use. In just a couple of hours, a complete beginner will be producing finished signs of all sizes with perfect results, completely unassisted. This means that you quickly start earning back your investment. Simply put, your profits start right from day one. Using ROLLSROLLER is like riding a bicycle – once you’ve learned, you never forget.
- Fast ROI
- Profitable
- Easy to learn
FLATBED APPLICATOR DOES THE JOB IN A THIRD OF THE TIME
Above all, the ROLLSROLLER Flatbed Applicator saves you time – lots of time! Many of our customers have reorganised their whole production process and significantly raised their profits – partly because the ROLLSROLLER increases their capacity and partly because they have more time for other activities, such as sales.
- Increased capacity
- Shorter delivery times
- More times for sales and customer care
PERFECT RESULTS EVERY TIME
With traditional application by hand or using a roll to roll laminator, the results are often unreliable and a certain amount of wastage is unavoidable. ROLLSROLLER Flatbed Applicator significantly improves the final results by producing higher quality every time – whoever is doing the job.
- Higher quality – no more bubbles and creases
- Less wastage
- Consistent high quality – every time
ERGONOMIC WORK POSITION
Manual application on very large signs requires a lot of climbing and knee-bending, which puts strain on the body. The ROLLSROLLER Flatbed Applicator gives you an ergonomic work station. And by choosing a height-adjustable table, you get even greater benefits and can reduce the long-term accident and sick-leave rate at your workplace.
- Better ergonomics
- Less strain on the body
- Less sick leave
FAQ - ROLLSROLLER
FAQ- ROLLSROLLER
THE RUBBER ROLLER WON’T MOVE UP AND DOWN
- Reset the emergency stop function
- Check the air connections
THE RUBBER ROLLER FALLS DOWN/GOES UNEVENLY
- Check air pressure
- Check green indicator lamp on the glide beam
- Look for leaking air connections
- Adjust the roller speed
THE MACHINE PULLS UNEVENLY DURING APPLICATION
- Check bearing play in the glide beam
- Perform a cross measurement of the roller
MACHINE CREATING CREASES/BUBBLES
- Perform a cross measurement of the roller
- Perform a pressure test and see if the roller presses evenly.
- Check quality of the vinyl/material. Has the liner been exposed to moisture?
- Try different method how to apply the vinyl
- If applying on boards, check thickness tolerances from the manufacturer of the boards
HEIGHT ADJUSTMENT
- Reset the system.
- Check main power.
- Unplug the socket to the main power, wait a few seconds. Plug the cable and reset again.
Resetting the height adjustable system:
- Disconnect power supply to the table, wait 60 seconds.
- Connect power supply, wait 25-30 seconds (the system feels that everything is connected.)
- Press the down key at one side and run the table into the lowest position. Hold the button during the hole process, legs will give a small motion up/down before reset is done.
- Repeat the reset (press down the down key) once again , to be sure that all the legs are in the lowest position.
- Now the system should be ok.
MAINTENANCE
EVERY DAY
- Make sure that the roller is not damaged and has nothing stuck to it.
- Check the emergency stop function and controls.
- Check visible cables for damages.
ONCE A WEEK
- Wipe any dust off the Glide beam’s sliding rails.
- Check filter regulator, empty for water if necessary.
- If your ROLLSROLLER has a compressor, see manual for maintenance instructions.
ONCE A MONTH
- Lubricate the sliding rails surfaces.
IF NECESSARY
- Check the bearing play in the Glide beam
- Dust the cutting mat with talcum powder
(The cutting mat is dusted with talcum powder at the factory, but should be dusted again when needed. The talcum powder prevents vinyl, adhesive and other materials from sticking to the cutting mat. It also reduces the risk of getting wrinkles/bubbles during application/lamination as the material can ”float” on the cu
Comments