Time to read: 6 min

HPE are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.

One of my favorite jobs as a mechanical engineer was as a heat exchanger designer for commercial aerospace. While it may appear straightforward, there are a lot of  considerations in good heat exchanger design, including: 

• Mechanical strength to resist bursting due to high pressure
• Geometry constraints (fitting effective heat exchangers into small footprints) 
• Fluid flow optimization and calculations 
• Pressure drop optimization
• Mechanical power needed to overcome fluid friction
• Heat transfer rate between fluids
• Fluid flow channel sizing and geometry (surface area density)
• Material selection for the coefficient of friction, coefficient of thermal expansion, heat transfer characteristics, and material compatibility

Now, I could rant for days about optimal fin design, methods for joining plates and fins, and even flow-stream mechanical energy losses, but this article is focused on material selection for heat exchanger design. Choosing the right material is critical to the success of your heat exchanger design because making a good choice enhances your design, while the wrong choice can cause it to fail. 

What Impact Does Material Selection Have on Heat Exchanger Performance?

Heat exchanger material should be chosen based on its physical material properties like thermal conductivity, temperature resistance, corrosion resistance, and strength &#; plus non-stable supply chain considerations such as cost and availability. The wrong material can lead to higher cost and longer production times if it&#;s more difficult to machine and weld. 

Material selection has a direct impact on the ability of the heat exchanger to exchange heat from one fluid to another. If you select a poor material, you&#;ll suffer negative impacts on the rate of heat transfer, drops in pressure, and you may even require excess mechanical power. On the other hand, correct material selection for heat exchanger design allows you to optimize performance, efficiency, cost, and potentially find savings in weight or achieve a smaller footprint.

What Material Properties Should You Look for In Heat Exchanger Design?

As mentioned above, these are the properties you should look to optimize when designing a heat exchanger: 

• Thermal Conductivity: Thermal conductivity is the measure of a material&#;s ability to transfer heat. Higher thermal conductivity materials allow more efficient heat transfer, which improves the performance of your design. 
• Temperature Resistance: Temperature resistance is the measure of a material&#;s ability to withstand high temperatures without deformation or compromising strength. 
• Density//Weight: Often, heat exchangers are designed for applications that require lightweight parts or where increases in weight decrease fuel efficiency &#; as with aerospace applications. 
• Corrosion Resistance: Corrosion resistance is the measure of a material&#;s ability to resist corrosion from chemical and environmental conditions and is especially critical if a heat exchanger will be subjected to harsh conditions. 
• Strength: Strength is the measure of a material&#;s ability to resist mechanical forces. Increased mechanical strength is required for applications that contain fluids at high pressure or will be subjected to heavier loads. 
• Cost and Availability: Cost and availability are self explanatory &#; you always want the best functional materials at the lowest cost.

Now, of course, not all materials provide an optimized combination of mechanical properties, cost, and availability &#; you&#;ll have to sacrifice one factor over the others to complete your design. 

Pro-tip: To see how material properties impact CNC machining and how to design for manufacturability, check out our on-demand webinar, DFM for CNC Machining: Minimize the Challenges with Design for CNC Machining. 

The Best Materials for Heat Exchanger Design

The best materials for heat exchanger design are materials with a combination of high thermal conductivity, high temperature resistance, excellent corrosion resistance, good mechanical strength, low cost, and wide availability. 

Copper is the most well-known metal with high electrical conductivity. Copper also has a high thermal conductivity due to its lattice-like atomic structure, which allows efficient energy conduction throughout the material. The number of free electrons in each atom of copper also allows for fast and efficient movement of energy via thermal or electrical conduction. This high thermal conductivity means that heat transfer from the hot to cold fluid will occur as efficiently as possible and with as much speed as possible. 

Copper also provides excellent corrosion resistance, fluid compatibility, and good mechanical strength. Copper comes in many alloys that are generally readily available and relatively inexpensive. In addition, it&#;s relatively easy to machine and weld, making it suitable for multiple manufacturing methods. Copper is especially suitable for tube and shell heat exchangers thanks to its high ductility &#; which allows it to be drawn into thin-walled tubes or extruded into small wires without fracturing.

Stainless steel is known for its high mechanical strength and excellent corrosion resistance, which comes from its naturally occurring, protective oxide layer. Stainless steel also has good thermal conductivity, which is why the material is an optimal choice for heat exchangers that must withstand ultra-high temperatures, high burst pressure, and extremely harsh environments. 

Stainless steel is stronger than aluminum, carbon steel, and copper, and its mechanical strength is preserved at higher temperatures than other common heat exchanger metals. This reduces the potential for distortion or warping over extended exposure to extreme temperatures. Stainless steel is also simple to machine and weld, which makes it easier to fabricate and assemble heat exchangers. 

For most commercial aircraft, various grades of aluminum are the predominant choice for heat exchanger material because it&#;s strong, yet lightweight. It&#;s the most common metal on earth, so it&#;s readily available and cost-effective. Aluminum also has a naturally occurring, protective oxide layer that can be modified to be stronger. Aluminum is ductile enough to be drawn into thin tubes or rolled into thin sheets and formed into fins with complex geometries. Aluminum also has excellent thermal conductivity, though it isn&#;t able to withstand temperatures above a few hundred degrees Fahrenheit. 

Aluminum can be readily brazed with methods like aluminum fluxless vacuum brazing, which creates a strong joint that can withstand the pressure of a heat exchanger. During brazing, the aluminum oxide layer cracks because it&#;s more brittle than the underlying metal. This cracking occurs at high temperatures right before the braze metal melts and fills the gaps between the oxide layer, and a gettering agent is used to prevent the oxides from reforming. While aluminum isn&#;t suitable for all heat exchanger applications, it&#;s generally the first material I would recommend. 

Titanium has only been prominently utilized in manufacturing since the early s. (Though it was discovered in by an English pastor!) Titanium has many excellent material properties that make it suitable for heat exchanger construction &#; it&#;s lightweight, corrosion-resistant, and has good heat transfer properties. I think of titanium as a supercharged cousin of aluminum that provides many of the same valuable material properties, but on a higher scale &#; except for its thermal conductivity, which is lower than aluminum. Still, titanium boasts the highest operating temperature on this list, and that tradeoff may be necessary in some applications. 

Titanium is about 1.5x more dense than aluminum, but its strength is 4-5x higher than aluminum, so using titanium can result in significant weight savings. However, a common misconception is that titanium is lighter weight than aluminum &#; the truth is that you get the same load capacity from less titanium than you get with the same amount of aluminum. This is why many aerospace companies, car manufacturers, and even medical device companies are utilizing titanium more in order to meet requirements to minimize weight and increase strength. 

Comparison of the Best Materials for Heat Exchanger Design

Now that you know the pros and cons of the materials, you can utilize the tables below &#; which have the key data points for each &#; to simplify material selection for your next heat exchanger design: 

Thermal Conductivity (BTU/hr*ft*F)Copper6.95Stainless Steel0.285Aluminum4.14Titanium0.15 Highest Operating Temperature (F)CopperStainless SteelAluminum300Titanium Density (lb/in^3) @ Room Temp (68F)Copper0.323Stainless Steel0.285Aluminum0.098Titanium0.163 Corrosion ResistanceCopperHighStainless SteelHighAluminumModerateTitaniumHigh Tensile Strength (lb/in^2)CopperStainless SteelAluminumTitanium

Key Takeaways: Heat Exchanger Material Selection

1. How do you select a material for a heat exchanger?
   
   Heat exchanger selection should involve a tradeoff between material properties like thermal conductivity, tensile strength, maximum operating temperature, density, and corrosion resistance versus availability and cost. 

2. What is the best material to use for a heat exchanger?
   
   Our recommendations for heat exchanger material are copper, stainless steel, aluminum or titanium.

3. What are the factors for selecting reliable heat exchanger tube materials?
   
   Fluid compatibility, tensile strength, and ductility are all important factors to consider when selecting a material for heat exchanger tubing. 

4. What is the best material for condensing heat exchanger for steam?

Stainless steel is a good choice for handling condensing steam heat exchanger applications because it&#;s corrosion-resistant, resistant to high temperatures, and thermally conductive. 

Complex Parts at Ridiculous Speeds &#; Start Your Next Project With Fictiv

For all your heat exchanger CNC machining and finishing needs, Fictiv has you covered. No matter how complex your designs, we&#;re experts at producing custom CNC machined tight tolerance parts in a variety of materials. We simplify custom part sourcing with intelligent, streamlined, automated workflows that deliver high quality mechanical components fast. Fictiv is your operating system for custom manufacturing that makes part procurement faster, easier, and more efficient.

 Create an account and upload your part to see what our instant quote process, design for manufacturability feedback, and intelligent platform can do for you.

Enhancing Efficiency with Stainless Steel Heat Exchangers

Aradhana Mantri

·

Follow

3 min read

Additional resources:
where to find stainless steel pipe
Cast Iron Pipes & Florida Homes Built Before 1975

For more stainless steel heat exchanger tubeinformation, please contact us. We will provide professional answers.

·

Feb 13,

--

Heat exchangers play a critical role in various industries, facilitating the transfer of heat between fluids while maintaining separation. Among the wide array of materials available for heat exchanger construction, 316 stainless steel stands out for its exceptional corrosion resistance, durability, and thermal conductivity.

Corrosion Resistance

The use of stainless steel heat exchangers offers unparalleled corrosion resistance, particularly in harsh environments where exposure to corrosive substances or high temperatures is inevitable. This corrosion resistance is attributed to the alloy&#;s composition, which includes chromium, nickel, and molybdenum, forming a protective oxide layer that prevents rust and deterioration over time. As a result, 316 stainless steel heat exchangers exhibit longevity and reliability, even in challenging operating conditions.

Durability

The robustness of 316 stainless steel makes it an ideal choice for heat exchanger applications that require resistance to mechanical stress, erosion, and thermal cycling. Whether in industrial processes, chemical plants, or marine environments, 316 stainless steel heat exchangers maintain their structural integrity and performance over extended periods, minimizing maintenance requirements and downtime.

Thermal Conductivity

316 stainless steel boasts excellent thermal conductivity, facilitating efficient heat transfer between fluids in heat exchanger systems. This property ensures rapid and uniform heating or cooling of the process fluids, optimizing energy efficiency and reducing operating costs. Whether in HVAC systems, power generation facilities, or food processing plants, 316 SS heat exchangers contribute to enhanced productivity and sustainability.

Types of Stainless Steel Heat Exchangers

Stainless steel heat exchangers are essential components in various industries, facilitating the efficient transfer of heat between fluids while ensuring durability and corrosion resistance. Here are some common types of stainless steel heat exchangers:

1. Shell and Tube Heat Exchangers:

• Shell and tube heat exchangers consist of a shell (outer vessel) and a series of tubes (inner vessels) through which the fluids flow. The fluids exchange heat as they pass through the tubes, with one fluid flowing inside the tubes (the tube side) and the other flowing outside the tubes (the shell side). Stainless steel tubes are often used in these exchangers due to their corrosion resistance and thermal conductivity.

2. Plate Heat Exchangers:

• Plate heat exchangers utilize a series of plates with alternating channels for the hot and cold fluids. The fluids flow in counter-current or co-current directions, allowing efficient heat transfer through the thin stainless steel plates. Plate heat exchangers are compact, lightweight, and offer high thermal efficiency, making them suitable for applications where space is limited or rapid heat transfer is required.

3. Finned Tube Heat Exchangers:

• Finned tube heat exchangers consist of stainless steel tubes with extended surfaces (fins) attached to increase the surface area available for heat transfer. These exchangers are particularly effective in air-to-fluid or gas-to-fluid heat transfer applications, such as air conditioning systems, refrigeration units, and industrial boilers.

4. Tube-in-Tube Heat Exchangers:

• Tube-in-tube heat exchangers feature concentric tubes nested within each other, with one fluid flowing through the inner tube and the other flowing through the annular space between the inner and outer tubes. This design allows for efficient heat transfer while maintaining a compact footprint, making tube-in-tube heat exchangers suitable for applications with limited space constraints.

5. Plate-Fin Heat Exchangers:

• Plate-fin heat exchangers consist of stacked plates with alternating layers of fins, creating a series of narrow passages for the fluids to flow through. These exchangers offer high heat transfer coefficients and are commonly used in aerospace, automotive, and cryogenic applications, where compactness and efficiency are paramount.

6. Spiral Heat Exchangers:

• Spiral heat exchangers feature two flat stainless steel plates wound into a spiral configuration, creating multiple parallel channels for fluid flow. This design promotes turbulent flow and enhances heat transfer efficiency, making spiral heat exchangers suitable for handling viscous fluids, slurries, and high fouling applications.

Applications

316 SS heat exchangers find applications across a diverse range of industries and processes, including:

• Chemical processing
• Petrochemical refineries
• Pharmaceutical manufacturing
• Food and beverage production
• HVAC and refrigeration systems
• Power generation and renewable energy

Conclusion

316 stainless steel heat exchangers offer an unbeatable combination of corrosion resistance, durability, and thermal conductivity, making them indispensable in critical industrial processes and applications. By harnessing the superior properties of 316 stainless steel, businesses can optimize efficiency, reduce maintenance costs, and ensure reliable operation of their heat exchanger systems for years to come.

Are you interested in learning more about inconel 625 tubing? Contact us today to secure an expert consultation!