HWGC P&P machines - Documentation, Discussion and Info

For example, do the dimensions include the pins?
What is the sync/pick tolerance?
What is the special Scan-R?
What is the Charactors-check?
What is the pick-H pressure offset?

Scan-R is when the default camera scan radius on the component is not enough to cover the entire component dimension. The default scan radius would fit nearly everything jelly beans and IC. But, if you have something larger like module, USB connector you enlarged this scan radius. To see the effects of this scan radius, go to any component feeder page, pick the component to the fast/high camera and play with the scan radius.

Charactors-check is used to detect if the component is picked but wrongly picked on the side which when looked on the camera, it pretty much a rectangular/square shape that look "legit" to the software. If you enabled this Charactors-check and set the percentage to say 25%, the software would then need to ensure when the component is imaged, it cannot be more/less than 25% off from the dimension (length and width) of the component you have entered. I find this most important with component that can bounced on the feeder and sit sideways on the tape. Of course, it reduced your job in touching up after placement but you lose a lot of components.

The other 2 parameters, I'm not too sure too.

Scan-R is when the default camera scan radius on the component is not enough to cover the entire component dimension. The default scan radius would fit nearly everything jelly beans and IC. But, if you have something larger like module, USB connector you enlarged this scan radius. To see the effects of this scan radius, go to any component feeder page, pick the component to the fast/high camera and play with the scan radius.Charactors-check is used to detect if the component is picked but wrongly picked on the side which when looked on the camera, it pretty much a rectangular/square shape that look "legit" to the software. If you enabled this Charactors-check and set the percentage to say 25%, the software would then need to ensure when the component is imaged, it cannot be more/less than 25% off from the dimension (length and width) of the component you have entered. I find this most important with component that can bounced on the feeder and sit sideways on the tape. Of course, it reduced your job in touching up after placement but you lose a lot of components.The other 2 parameters, I'm not too sure too.

Read more

Yamaha Electric Feeder 8mm 12mm 16mm for DIY SMT Pick and Place Machine

Description

Yamaha Electric Feeder 8mm 12mm 16mm For DIY SMT Pick And Place Machine

 

Description:

This kind of electric feeder comes with wire, the wire connects directly to machine connector.

The pin on feeder gets signal from air coming out from machine's hole making it advance.

Electric feeder without air impact, it is more stable and no noise.

 

Yamaha Electric feeder 8mm , 12mm , 16mm, 24mm , 32mm, 44mm SMT feeder

8mm type suitable , , , , &#;...etc.

These feeders suitable for :  Charmhigh machine or DIY pick and place machine or other brands smt machines in China

If you are not sure about the wire connections, please send images of your machine to us and we will give recommendation.

 .

8mm electric equal to 3 kinds of feeder:  

- 8*2mm pneumatic feeder

- 8*4mm pneumatic feeder

- CL pneumatic feeder 

 

Detail pictures:

 

 

Option: 8mm, 12mm ,16mm (thin slot) 

12mm: 2.5mm slot depth,  16mm: 6mm slot depth

KF-SMT Product Page

24mm, 32mm, 44mm with deep slot 14mm which can install deep reel.

 

Compare: pneumatic feeder & electric feeder, electric feeder moving peaceful and smoothy: 

 

There are also wireless type Yamaha electric feeder, here are the pictures installing on pick and place machine: (pneumatic + electric together)

 

Can DIY your pick and place machine, install a Conductive copper sheet on machine like this:

 

Service & Warranty:

The complete machine has a warranty period of 1 year from the time of purchase and lifetime service.

We always provide spare parts of machine, factory reliable direct supply.

We provide online Q/A and troubleshooting support and technical advice service.

 

If you want to see more information and videos, please contact us by .

We will response you at the first time.

 

Competitive Advantage

1. Friendly and professional customer service people help you in 16 hours.
2. More than 10 years powerful ODM/OEM ability,could make product shape design,custom logo,custom package.
3. We can provide not only product, but also system software management.Save your time and cost.
4. Special service from Goldantell: For repairing,no need you return back product,only need you take a video,our engineer will instruct you,if spare parts was damaged in 1 year,we will send you spare parts by fastest express,you no need bear any fee.